Grinder compatibility and adapters

CremaLoop slow feeders mount on your grinder’s throat with a grinder-specific adapter. Choosing the feeder is the easy part, choosing the adapter is what most questions are about.

One feeder fits every adapter

All feeder bodies - Metal, Ultra, Pro V1 and Pro V2 - share the same bottom design, so every published grinder adapter fits every feeder. Using one feeder across several grinders is fully supported: buy one feeder plus a stand-alone adapter for each grinder.

How adapters are sold

Which route you need depends only on whether your grinder is in the table below.

Your grinder is in the list below → Feeder variant for your grinderMetal: adapter included. Ultra: adapter as an add-on.

You have a feeder and add a grinder → Stand-alone adapterEvery adapter fits every feeder

Your grinder is not listed → Custom adapterSend us two measurements (see below)

Order links: stand-alone grinder adapter · custom adapter.

A stand-alone feeder without any adapter is also available, which is what you want if you are only adding a custom adapter.

Metal or printed depends on the grinder

Adapters exist in metal for some grinders and as printed parts for others. Which one you get is shown on the product page for your grinder, so please check there rather than assuming. New metal adapters are added over time, and we poll the CremaLoop newsletter on which to manufacture next.

Find your grinder

Grinder	Notes
Acaia Orbit	Adapter available - installs in the metal grinder funnel
Baratza Sette 270 / 30	Adapter available
Bentwood V63 - V73	Adapter available
Ceado E37S, E37SD, E37Z Naked, E5SD, E6C Chameleon, Life	Adapter available
DF54, DF64V (incl. Gen 3)	Adapter available; DF64V Gen 3 uses the same adapter as earlier DF64V
DF64 (Gen 1/2), DF64P/E	Adapter available; a tilted base stand accessory exists for DF64 Gen 1/2
DF83, DF83V	Adapter available
Emil T64S	Adapter available
Eureka Mignon (incl. AP 65), Eureka MCI	Adapter available; the Single Dose Bellow also fits the Mignon AP 65
Fellow Ode Gen 1 & 2	Adapter available
Fellow Opus	Adapter available
Femobook A4Z, A68	Adapter available
Fiorenzato F4 / Allground, Sanremo Allground	Adapter available
Geimori GU64	Adapter available
Gevi Grindmaster	Adapter available
KafaTek Monolith Conical (MC6) / Flat / SDRM	Adapter available - mounts into the bottom funnel: remove the top funnel / anti-popcorn lid first (it’s held by an O-ring and pulls off gently)
KafaTek MAX, M98V	Adapter available
Mahlkönig EK43, EK43S, EK Omnia	Adapter available
Mahlkönig X54, X64 SD	Adapter available
Mazzer Super Jolly / Mini / Lux	Adapter available
Mazzer Philos	Adapter available
MHW-3Bomber Sniper	Adapter available
Niche Zero	Adapter available - has a pin that presses the grinder’s safety button. Does not fit the Niche Duo (different inlet; no Duo adapter currently)
Option-O Lagom P64	Adapter available - for the updated design (2022 and newer)
Option-O Lagom P80, P100	Adapter available
Option-O Lagom 01	Adapter available
Option-O Lagom Casa	Adapter available
Shardor / Mokkom (64 mm inlet)	The Shardor 64 mm adapter fits: 52 mm inner diameter, 64 mm outer, covering the whole inlet
Timemore 078 / 078S, 064 / 064S	Adapter available; improved hopper/dosing-cup lid accessory available
Titus Nautilus	Adapter available - fits the grinder inlet
Varia VS3, VS6	Adapter available
Weber Workshops EG-1	Adapter available - see the fit note below
Wendougee Milo Play	Adapter available
WPM ZP-1 / Domus / Konos	Adapter available
xBloom Studio	Adapter available
Zerno Z1 / Z2	Adapter available - two install options, see the note below

Open the matching product on cremaloop.com to confirm the exact adapter, or contact us with your grinder model.

Your grinder is not listed

We can almost always make one. Send us two measurements from the grinder inlet:

Measure in millimetres, and add a photo of the inlet taken from directly above.

Add a photo of the inlet taken from directly above. We will check whether an existing adapter already fits before making a new one, then order it as a custom adapter.

If you would rather print your own

The feeder needs a 56 mm hole in whatever it sits on. That is the only dimension that matters on the feeder side, so an existing lid mod for your grinder can be adapted by opening it up to 56 mm.

Notes for specific grinders

Zerno Z1 and Z2. There are two ways to fit the feeder: directly into the grinder inlet with the stock funnel removed, or into a funnel - the stock one, or a third-party funnel such as Introvertmakes. We usually recommend fitting it directly into the grinder. Do not simply rest the feeder on the stock funnel: it is unstable that way and can fall off.

Weber EG-1. All our feeders work with the EG-1 adapter, but the plastic-bodied feeders sit a little looser on it. The Slow Feeder Metal has a sealing ring that gives a firmer fit, so that is the pairing we recommend.

Why some adapters tilt forward

Some adapters are deliberately angled so the feeder leans slightly forward. This is by design, not a fault or a wrong part: the forward tilt stops beans sitting in the feeder holes without dropping through. If your adapter looks tilted, it is meant to.

Adapters & accessories

• Grinder adapters (black, and white/silver finishes) - match the adapter to your grinder
• Single Dose Bellow & Lid - optional accessory (listed in the manual)
• Replacement parts - see product pages on cremaloop.com

Keeping this current

This table mirrors the grinder list on the adapter product page (checked 2026-10-30). If your grinder is in that dropdown but missing here, it is a standard adapter - order it there. As exact adapter SKUs per grinder are confirmed, the table above will gain an “adapter SKU” column.